 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HCS320 KEELOQ(R) Code Hopping Encoder FEATURES Security Programmable 28-bit serial number Programmable 64-bit encryption key Each transmission is unique 66-bit transmission code length 32-bit hopping code 34-bit fixed code (28-bit serial number, 4-bit function code, 2-bit status) * Encryption keys are read protected * * * * * * DESCRIPTION The HCS320 from Microchip Technology Inc. is a code hopping encoder designed for secure Remote Keyless Entry (RKE) systems. The HCS320 utilizes the code hopping technology which incorporates high security, a small package outline, and low cost, to make this device a perfect solution for unidirectional remote keyless entry systems and access control systems. PACKAGE TYPES PDIP, SOIC S0 S1 S2 SHIFT 1 HCS320 2 3 4 8 7 6 5 VDD LED PWM VSS Operating * * * * * * * * 3.5V - 13.0V operation Shift key and three inputs 16 functions available Selectable baud rate Automatic code word completion Battery low signal transmitted to receiver Battery low indication on LED Non-volatile synchronization data HCS320 BLOCK DIAGRAM Oscillator RESET circuit LED LED driver Controller Power latching and switching Other * * * * * * Easy-to-use programming interface On-chip EEPROM On-chip oscillator and timing components Button inputs have internal pull-down resistors Current limiting on LED output Low external component cost EEPROM Encoder PWM 32-bit shift register Typical Applications VSS The HCS320 is ideal for Remote Keyless Entry (RKE) applications. These applications include: * * * * * * Automotive RKE systems Automotive alarm systems Automotive immobilizers Gate and garage door openers Identity tokens Burglar alarm systems Button input port VDD SHIFT S2 S1 S0 The HCS320 combines a 32-bit hopping code generated by a nonlinear encryption algorithm, with a 28-bit serial number and six status bits to create a 66-bit transmission stream. The length of the transmission eliminates the threat of code scanning and the code hopping mechanism makes each transmission unique, thus rendering code capture and resend (code grabbing) schemes useless. (c) 2001 Microchip Technology Inc. DS41097C-page 1 HCS320 The crypt key, serial number and configuration data are stored in an EEPROM array which is not accessible via any external connection. The EEPROM data is programmable but read-protected. The data can be verified only after an automatic erase and programming operation. This protects against attempts to gain access to keys or manipulate synchronization values. The HCS320 provides an easy-to-use serial interface for programming the necessary keys, system parameters and configuration data. * Learn - Learning involves the receiver calculating the transmitter's appropriate crypt key, decrypting the received hopping code and storing the serial number, synchronization counter value and crypt key in EEPROM. The KEELOQ product family facilitates several learning strategies to be implemented on the decoder. The following are examples of what can be done. - Simple Learning The receiver uses a fixed crypt key, common to all components of all systems by the same manufacturer, to decrypt the received code word's encrypted portion. - Normal Learning The receiver uses information transmitted during normal operation to derive the crypt key and decrypt the received code word's encrypted portion. - Secure Learn The transmitter is activated through a special button combination to transmit a stored 60-bit seed value used to generate the transmitter's crypt key. The receiver uses this seed value to derive the same crypt key and decrypt the received code word's encrypted portion. * Manufacturer's code - A unique and secret 64bit number used to generate unique encoder crypt keys. Each encoder is programmed with a crypt key that is a function of the manufacturer's code. Each decoder is programmed with the manufacturer code itself. The HCS320 code hopping encoder is designed specifically for keyless entry systems; primarily vehicles and home garage door openers. The encoder portion of a keyless entry system is integrated into a transmitter, carried by the user and operated to gain access to a vehicle or restricted area. The HCS320 is meant to be a cost-effective yet secure solution to such systems, requiring very few external components (Figure 2-1). Most low-end keyless entry transmitters are given a fixed identification code that is transmitted every time a button is pushed. The number of unique identification codes in a low-end system is usually a relatively small number. These shortcomings provide an opportunity for a sophisticated thief to create a device that `grabs' a transmission and retransmits it later, or a device that quickly `scans' all possible identification codes until the correct one is found. The HCS320 on the other hand, employs the KEELOQ code hopping technology coupled with a transmission length of 66 bits to virtually eliminate the use of code `grabbing' or code `scanning'. The high security level of the HCS320 is based on the patented KEELOQ technology. A block cipher based on a block length of 32 bits and a key length of 64 bits is used. The algorithm obscures the information in such a way that even if the transmission information (before coding) differs by only one bit from that of the previous transmission, the next 1.0 SYSTEM OVERVIEW Key Terms The following is a list of key terms used throughout this data sheet. For additional information on KEELOQ and Code Hopping, refer to Technical Brief 3 (TB003). * RKE - Remote Keyless Entry * Button Status - Indicates what button input(s) activated the transmission. Encompasses the 4 button status bits S3, S2, S1 and S0 (Figure 4-2). * Code Hopping - A method by which a code, viewed externally to the system, appears to change unpredictably each time it is transmitted. * Code word - A block of data that is repeatedly transmitted upon button activation (Figure 4-1). * Transmission - A data stream consisting of repeating code words (Figure 8-2). * Crypt key - A unique and secret 64-bit number used to encrypt and decrypt data. In a symmetrical block cipher such as the KEELOQ algorithm, the encryption and decryption keys are equal and will therefore be referred to generally as the crypt key. * Encoder - A device that generates and encodes data. * Encryption Algorithm - A recipe whereby data is scrambled using a crypt key. The data can only be interpreted by the respective decryption algorithm using the same crypt key. * Decoder - A device that decodes data received from an encoder. * Decryption algorithm - A recipe whereby data scrambled by an encryption algorithm can be unscrambled using the same crypt key. DS41097C-page 2 (c) 2001 Microchip Technology Inc. HCS320 coded transmission will be completely different. Statistically, if only one bit in the 32-bit string of information changes, greater than 50 percent of the coded transmission bits will change. As indicated in the block diagram on page one, the HCS320 has a small EEPROM array which must be loaded with several parameters before use; most often programmed by the manufacturer at the time of production. The most important of these are: * A 28-bit serial number, typically unique for every encoder * A crypt key * An initial 16-bit synchronization value * A 16-bit configuration value The crypt key generation typically inputs the transmitter serial number and 64-bit manufacturer's code into the key generation algorithm (Figure 1-1). The manufacturer's code is chosen by the system manufacturer and must be carefully controlled as it is a pivotal part of the overall system security. FIGURE 1-1: Production Programmer CREATION AND STORAGE OF CRYPT KEY DURING PRODUCTION HCS320 EEPROM Array Serial Number Crypt Key Sync Counter Transmitter Serial Number Manufacturer's Code Key Generation Algorithm Crypt Key . . . The 16-bit synchronization counter is the basis behind the transmitted code word changing for each transmission; it increments each time a button is pressed. Due to the code hopping algorithm's complexity, each increment of the synchronization value results in greater than 50% of the bits changing in the transmitted code word. Figure 1-2 shows how the key values in EEPROM are used in the encoder. Once the encoder detects a button press, it reads the button inputs and updates the synchronization counter. The synchronization counter and crypt key are input to the encryption algorithm and the output is 32 bits of encrypted information. This data will change with every button press, its value appearing externally to `randomly hop around', hence it is referred to as the hopping portion of the code word. The 32-bit hopping code is combined with the button information and serial number to form the code word transmitted to the receiver. The code word format is explained in greater detail in Section 4.0. A receiver may use any type of controller as a decoder, but it is typically a microcontroller with compatible firmware that allows the decoder to operate in conjunction with an HCS320 based transmitter. Section 7.0 provides detail on integrating the HCS320 into a system. A transmitter must first be `learned' by the receiver before its use is allowed in the system. Learning includes calculating the transmitter's appropriate crypt key, decrypting the received hopping code and storing the serial number, synchronization counter value and crypt key in EEPROM. In normal operation, each received message of valid format is evaluated. The serial number is used to determine if it is from a learned transmitter. If from a learned transmitter, the message is decrypted and the synchronization counter is verified. Finally, the button status is checked to see what operation is requested. Figure 13 shows the relationship between some of the values stored by the receiver and the values received from the transmitter. (c) 2001 Microchip Technology Inc. DS41097C-page 3 HCS320 FIGURE 1-2: EEPROM Array Crypt Key Sync Counter Serial Number BUILDING THE TRANSMITTED CODE WORD (ENCODER) KEELOQ Encryption Algorithm Button Press Information Serial Number 32 Bits Encrypted Data Transmitted Information FIGURE 1-3: BASIC OPERATION OF RECEIVER (DECODER) 1 Received Information EEPROM Array Button Press Information Serial Number 32 Bits of Encrypted Data Manufacturer Code 2 Check for Match Serial Number Sync Counter Crypt Key 3 KEELOQ Decryption Algorithm Decrypted Synchronization Counter Perform Function 5 Indicated by button press 4 Check for Match NOTE: Circled numbers indicate the order of execution. DS41097C-page 4 (c) 2001 Microchip Technology Inc. HCS320 2.0 DEVICE OPERATION TABLE 2-1: Name S0 S1 S2 SHIFT VSS PWM Pin Number 1 2 3 4 5 6 PIN DESCRIPTIONS Description Switch input 0 Switch input 1 Switch input 2/Clock pin when in Programming mode Switch input for Shift Ground reference Pulse Width Modulation (PWM) output pin / Data pin for Programming mode Cathode connection for LED Positive supply voltage As shown in the typical application circuits (Figure 2-1), the HCS320 is a simple device to use. It requires only the addition of buttons and RF circuitry for use as the transmitter in your security application. A description of each pin is described in Table 2-1. FIGURE 2-1: +12V R (2) TYPICAL CIRCUITS B0 B1 S0 S1 S2 SHIFT VDD LED PWM VSS Tx out LED VDD 7 8 2 button remote control +12V SHIFT B3 B2 B1 B0 R (2) S0 S1 S2 SHIFT VDD LED PWM VSS Tx out The HCS320 will wake-up upon detecting a button press and delay approximately 10 ms for button debounce (Figure 2-2). The synchronization counter, discrimination value and button information will be encrypted to form the hopping code. The hopping code portion will change every transmission, even if the same button is pushed again. A code word that has been transmitted will not repeat for more than 64K transmissions. This provides more than 18 years of use before a code is repeated; based on 10 operations per day. Overflow information sent from the encoder can be used to extend the number of unique transmissions to more than 192K. If in the transmit process it is detected that a new button(s) has been pressed, a RESET will immediately occur and the current code word will not be completed. Please note that buttons removed will not have any effect on the code word unless no buttons remain pressed; in which case the code word will be completed and the power-down will occur. 5 button remote control(1) Note 1: The full 16 function codes are implemented using the shift button. 2: Resistor R is recommended for current limiting. (c) 2001 Microchip Technology Inc. DS41097C-page 5 HCS320 FIGURE 2-2: ENCODER OPERATION Power-Up 3.0 (Button pressed) Set TX:= OFF EEPROM MEMORY ORGANIZATION RESET and Debounce Delay (10 ms) Transmit Button Pressed? No Increment Shift Level Stop Transmit Yes The HCS320 contains 192 bits (12 x 16-bit words) of EEPROM memory (Table 3-1). This EEPROM array is used to store the encryption key information, synchronization value, etc. Further descriptions of the memory array is given in the following sections. TABLE 3-1: Set TX:=ON WORD ADDRESS 0 No Yes 1 2 3 EEPROM MEMORY MAP MNEMONIC KEY_0 KEY_1 KEY_2 KEY_3 SYNC DESCRIPTION 64-bit encryption key (word 0) LSb's 64-bit encryption key (word 1) 64-bit encryption key (word 2) 64-bit encryption key (word 3) MSb's 16-bit synchronization value Device Serial Number (word 0) LSb's Shift Button Pressed? Yes TX=ON? Yes Update Sync Info Encrypt With Crypt Key Load Transmit Register 4 5 6 7 8 RESERVED Set to 0000H SER_0 No SER_1(Note) Device Serial Number (word 1) MSb's -- -- CONFIG Not used Not used Configuration Word Transmit 9 10 11 Note: No RESERVED Set to 0000H The MSB of the serial number contains a bit used to select the Auto-shutoff timer. Buttons Added? No All Buttons Released? Yes TX=ON? Yes Complete Code Word Transmission Stop No 3.1 KEY_0 - KEY_3 (64-Bit Crypt Key) The 64-bit crypt key is used to create the encrypted message transmitted to the receiver. This key is calculated and programmed during production using a key generation algorithm. The key generation algorithm may be different from the KEELOQ algorithm. Inputs to the key generation algorithm are typically the transmitter's serial number and the 64-bit manufacturer's code. While the key generation algorithm supplied from Microchip is the typical method used, a user may elect to create their own method of key generation. This may be done providing that the decoder is programmed with the same means of creating the key for decryption purposes. DS41097C-page 6 (c) 2001 Microchip Technology Inc. HCS320 3.2 SYNC (Synchronization Counter) 3.5 CONFIG (Configuration Word) This is the 16-bit synchronization value that is used to create the hopping code for transmission. This value will be changed after every transmission. The Configuration Word is a 16-bit word stored in EEPROM array that is used by the device to store information used during the encryption process, as well as the status of option configurations. The following sections further explain these bits. 3.3 Reserved Must be initialized to 0000H. TABLE 3-2: Bit Number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CONFIGURATION WORD Bit Description Discrimination Bit 0 Discrimination Bit 1 Discrimination Bit 2 Discrimination Bit 3 Discrimination Bit 4 Discrimination Bit 5 Discrimination Bit 6 Discrimination Bit 7 Discrimination Bit 8 Discrimination Bit 9 Overflow Bit 0 (OVR0) Overflow Bit 1 (OVR1) Low Voltage Trip Point Select (VLOW SEL) Baud rate Select Bit 0 (BSL0) Baud rate Select Bit 1 (BSL1) Reserved, set to 0 3.4 SER_0, SER_1 (Encoder Serial Number) SER_0 and SER_1 are the lower and upper words of the device serial number, respectively. Although there are 32 bits allocated for the serial number, only the lower order 28 bits are transmitted. The serial number is meant to be unique for every transmitter. The Most Significant bit of the serial number (Bit 31) is used to turn the Auto-shutoff timer on or off. 3.4.1 AUTO-SHUTOFF TIMER ENABLE The Most Significant bit of the serial number (Bit 31) is used to turn the Auto-shutoff timer on or off. This timer prevents the transmitter from draining the battery should a button get stuck in the on position for a long period of time. The time period is approximately 25 seconds, after which the device will go to the Timeout mode. When in the Time-out mode, the device will stop transmitting, although since some circuits within the device are still active, the current draw within the Shutoff mode will be more than Standby mode. If the Most Significant bit in the serial number is a one, then the Auto-shutoff timer is enabled, and a zero in the Most Significant bit will disable the timer. The length of the timer is not selectable. 3.5.1 DISCRIMINATION VALUE (DISC0 TO DISC9) The discrimination value aids the post-decryption check on the decoder end. It may be any value, but in a typical system it will be programmed as the 10 Least Significant bits of the serial number. Values other than this must be separately stored by the receiver when a transmitter is learned. The discrimination bits are part of the information that form the encrypted portion of the transmission (Figure 4-2). After the receiver has decrypted a transmission, the discrimination bits are checked against the receiver's stored value to verify that the decryption process was valid. If the discrimination value was programmed as the 10 LSb's of the serial number then it may merely be compared to the respective bits of the received serial number; saving EEPROM space. 3.5.2 OVERFLOW BITS (OVR0, OVR1) The overflow bits are used to extend the number of possible synchronization values. The synchronization counter is 16 bits in length, yielding 65,536 values before the cycle repeats. Under typical use of 10 operations a day, this will provide nearly 18 years of use before a repeated value will be used. Should the system designer conclude that is not adequate, then the overflow bits can be utilized to extend the number (c) 2001 Microchip Technology Inc. DS41097C-page 7 HCS320 of unique values. This can be done by programming OVR0 and OVR1 to 1s at the time of production. The encoder will automatically clear OVR0 the first time that the synchronization value wraps from 0xFFFF to 0x0000 and clear OVR1 the second time the counter wraps. Once cleared, OVR0 and OVR1 cannot be set again, thereby creating a permanent record of the counter overflow. This prevents fast cycling of 64K counter. If the decoder system is programmed to track the overflow bits, then the effective number of unique synchronization values can be extended to 196,608. 3.5.4 LOW VOLTAGE TRIP POINT SELECT The low voltage trip point select bit is used to tell the HCS320 what VDD level is being used. This information will be used by the device to determine when to send the voltage low signal to the receiver. When this bit is set to a one, the VDD level is assumed to be operating from a 9.0 volt or 12.0 volt VDD level. If the bit is set low, then the VDD level is assumed to be 6.0 volts. Refer to Figure 3-1 for voltage trip point. 3.5.3 BAUD RATE SELECT BITS (BSL0, BSL1) FIGURE 3-1: VOLTAGE TRIP POINTS BY CHARACTERIZATION) VLOW sel = 0 VLOW BSL0 and BSL1 select the speed of transmission and the code word blanking. Table 3-3 shows how the bits are used to select the different baud rates and Section 5.6 provides detailed explanation in code word blanking. Volts (V) 5.5 5.0 4.5 4.0 Max TABLE 3-3: BSL1 0 0 1 1 BSL0 0 1 0 1 BAUD RATE SELECT Basic Pulse Element 400 s 200 s 100 s 100 s Code Words Transmitted All 1 out of 2 1 out of 2 1 out of 4 3.5 3.0 2.5 Min 9.0 8.5 8.0 7.5 7.0 -40 -20 0 20 VLOW sel = 1 Max Min 40 60 80 100 Temp (C) DS41097C-page 8 (c) 2001 Microchip Technology Inc. HCS320 4.0 4.1 TRANSMITTED WORD Code Word Format 4.2 Code Word Organization The HCS320 code word is made up of several parts (Figure 4-1). Each code word contains a 50% duty cycle preamble, a header, 32 bits of encrypted data and 34 bits of fixed data followed by a guard period before another code word can begin. Refer to Table 8-3 for code word timing. The HCS320 transmits a 66-bit code word when a button is pressed. The 66-bit word is constructed from a Fixed Code portion and an Encrypted Code portion (Figure 4-2). The 32 bits of Encrypted Data are generated from 4 button bits, 12 discrimination bits and the 16-bit sync value. The encrypted portion alone provides up to four billion changing code combinations. The 34 bits of Fixed Code Data are made up of 2 status bits, 4 button bits and the 28-bit serial number. The fixed and encrypted sections combined increase the number of code combinations to 7.38 x 1019. FIGURE 4-1: CODE WORD FORMAT TE TE TE LOGIC `0' LOGIC `1' Bit Period 50% Duty Cycle Preamble TP Encrypted Portion of Transmission THOP Fixed Portion of Transmission TFIX Guard Time TG Header TH FIGURE 4-2: CODE WORD ORGANIZATION 34 bits of Fixed Portion 32 bits of Encrypted Portion Function Code (4-bit) OVR (2 bits) DISC (10 bits) Sync Counter (16 bits) LSb Repeat VLOW (1-bit) (1-bit) MSb Function Code (4-bit) Serial Number (28 bits) 66 Data bits Transmitted LSb first. (c) 2001 Microchip Technology Inc. DS41097C-page 9 HCS320 4.3 Synchronous Transmission Mode Synchronous Transmission mode can be used to clock the code word out using an external clock. To enter Synchronous Transmission mode, the Programming mode start-up sequence must be executed as shown in Figure 4-3. If either S1 or S0 is set on the falling edge of S2, the device enters Synchronous Transmission mode. In this mode, it functions as a normal transmitter, with the exception that the timing of the PWM data string is controlled externally and 16 extra bits are transmitted at the end with the code word. The button code will be the S0, S1 value at the falling edge of S2. The timing of the PWM data string is controlled by supplying a clock on S2 and should not exceed 20 kHz. The code word is the same as in PWM mode with 16 reserved bits at the end of the word. The reserved bits can be ignored. When in Synchronous Transmission mode S2 should not be toggled until all internal processing has been completed as shown in Figure 4-4. FIGURE 4-3: SYNCHRONOUS TRANSMISSION MODE t = 50ms Preamble Header Data TPS TPH1 TPH2 PWM S2 S[1:0] "01,10,11" FIGURE 4-4: CODE WORD ORGANIZATION (SYNCHRONOUS TRANSMISSION MODE) Fixed Portion Encrypted Portion Serial Number (28 bits) Function Code (4-bit) DISC+ OVR (12 bits) Sync Counter (16 bits) LSb Reserved (16 bits) MSb Padding (2 bits) Function Code (4-bit) 82 Data bits Transmitted LSb first. DS41097C-page 10 (c) 2001 Microchip Technology Inc. HCS320 5.0 5.1 SPECIAL FEATURES Code Word Completion 5.3 VLOW: Voltage LOW Indicator Code word completion is an automatic feature that makes sure that the entire code word is transmitted, even if the transmit button is released before the transmission is complete. The HCS320 encoder powers itself up when a button is pushed and powers itself down after the command is finished, if the user has already released the button. If the button is held down beyond the time for one transmission, then multiple transmissions will result. If another button is activated during a transmission, the active transmission will be aborted and the function new code will be generated using the new button information. The VLOW bit is transmitted with every transmission (Figure 8-6) and will be transmitted as a one if the operating voltage has dropped below the low voltage trip point. The trip point is selectable between two values, based on the battery voltage being used. See Section 3.5.4 for a description of how the low voltage select option is set. This VLOW signal is transmitted so the receiver can alert the user that the transmitter battery is low. Note: Depending on the internal resistance of the VDD source, VDD may normally be above the VLOW trip point except when the LED is turned on. In this case, the VLOW bit will be transmitted as a one when a transmission occurs while the LED is on. The VLOW bit will be transmitted as a zero when a transmission occurs while the LED is off. 5.2 Auto-Shutoff The Auto-shutoff function automatically stops the device from transmitting if a button inadvertently gets pressed for a long period of time. This will prevent the device from draining the battery if a button gets pressed while the transmitter is in a pocket or purse. This function can be enabled or disabled and is selected by setting or clearing the Auto-shutoff bit (Section 3.4.1). Setting this bit high will enable the function (turn Auto-shutoff function on) and setting the bit low will disable the function. Time-out period is dependent on the shift level and is approximately 42 10 seconds. 5.4 RPT: Repeat Indicator This bit will be low for the first transmitted word. If a button is held down for more than one transmitted code word, this bit will be set to indicate a repeated code word and remain set until the button is released. 5.5 LED Output Operation During normal transmission the LED output (Figure 5-1) indicates the shift level (Section 5.7) by flashing the LED in a pattern corresponding to the shift level. If the supply voltage drops below the low voltage trip point (Section 3.5.4), the LED output will be toggled at approximately 5 Hz during the transmission. FIGURE 5-1: SHIFT LEVEL LED FLASH FUNCTION (EACH DIVISION - 180 MS) LED OUTPUT 0 1 2 3 (c) 2001 Microchip Technology Inc. DS41097C-page 11 HCS320 5.6 Blank Alternate Code Word Federal Communications Commission (FCC) part 15 rules specify the limits on fundamental power and harmonics that can be transmitted. Power is calculated on the worst case average power transmitted in a 100 ms window. It is therefore advantageous to minimize the duty cycle of the transmitted word. This can be achieved by minimizing the duty cycle of the individual bits and by blanking out consecutive words. Blank Alternate Code Word (BACW) is used for reducing the average power of a transmission (Figure 5-1). This is a selectable feature that is determined in conjunction with the baud rate selection bits BSL0 and BSL1. Using the BACW allows the user to transmit a higher amplitude transmission if the transmission length is shorter. The FCC puts constraints on the average power that can be transmitted by a device, and BACW effectively prevents continuous transmission by only allowing the transmission of every second or every fourth code word. This reduces the average power transmitted and hence, assists in FCC approval of a transmitter device. FIGURE 5-2: BLANK ALTERNATE CODE WORD (BACW) Amplitude BACW Disabled (All words transmitted) BACW Enabled (1 out of 2 transmitted) A Code Word Code Word Code Word Code Word 2A BACW Enabled (1 out of 4 transmitted) 4A Time DS41097C-page 12 (c) 2001 Microchip Technology Inc. HCS320 5.7 SHIFT Key Operation TABLE 5-1: SHIFT LEVEL PIN ACTIVATION TABLE S2 0 0 0 0 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 1 S1 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 S0 0 1 0 1 0 0 1 0 1 0 0 1 0 1 0 0 1 0 1 0 FUNCTION CODE No Transmission 0h 1h 2h 3h No Transmission 4h 5h 6h 7h No Transmission 8h 9h Ah Bh No Transmission Ch Dh Eh Fh The HCS320 has four switch inputs usually connected to buttons as shown in Figure 2-1: Typical Circuits. Any button connected to input S0, S1 or S2 is called a TRANSMIT button as it causes a transmission when pressed. The SHIFT button is connected to the SHIFT input. Pressing the SHIFT button increments a counter by one count and does not result in a transmission. The counter value is called the shift level. Successive presses of the SHIFT button can increase the shift level up to three before wrapping back to zero. The shift level is available for eight seconds when the SHIFT button is released, after which the shift level is reset to zero. When a TRANSMIT button is pressed, the function code transmitted for that button depends on the shift level. The transmitted function code corresponding to shift level and S0, S1 and S2 switch activation is shown in Table 5-1 for all legal combinations of shift level and button input. Note that a shift level of zero means that the SHIFT button has not been pressed (or it has been pressed four times). The shift level is reset to zero after a transmission. The volatile nature of the shift level register requires the HCS320 to be powered continuously for correct operation and not powered via the buttons. 0 0 0 0 0 1 1 1 1 1 2 2 2 2 2 3 3 3 3 3 (c) 2001 Microchip Technology Inc. DS41097C-page 13 HCS320 6.0 PROGRAMMING THE HCS320 When using the HCS320 in a system, the user will have to program some parameters into the device including the serial number and the secret key before it can be used. The programming cycle allows the user to input all 192 bits in a serial data stream, which are then stored internally in EEPROM. Programming will be initiated by forcing the PWM line high, after the S2 line has been held high for the appropriate length of time line (Table 6-1 and Figure 6-1). After the Program mode is entered, a delay must be provided to the device for the automatic bulk write cycle to complete. This will set all locations in the EEPROM to zeros . The device can then be programmed by clocking in 16 bits at a time, using S2 as the clock line and PWM as the data in line. After each 16-bit word is loaded, a programming delay is required for the internal program cycle to complete. This delay can take up to TWC. At the end of the programming cycle, the device can be verified (Figure 6-2) by reading back the EEPROM. Reading is done by clocking the S2 line and reading the data bits on PWM. For security reasons, it is not possible to execute a verify function without first programming the EEPROM. A Verify operation can only be done once, immediately following the Program cycle. Note: To ensure that the device does not accidentally enter Programming mode, PWM should never be pulled high by the circuit connected to it. Special care should be taken when driving PNP RF transistors. FIGURE 6-1: PROGRAMMING WAVEFORMS TPBW TCLKH TDS TWC Enter Program Mode S2 (Clock) TPS TPH1 PWM (Data) TPH2 TCLKL Bit 0 Bit 1 Bit 2 TDH Bit 3 Bit 14 Bit 15 Bit 16 Bit 17 Data for Word 0 (KEY_0) Repeat for each word (12 times) Data for Word 1 Note 1: Unused button inputs to be held to ground during the entire programming sequence. 2: The VDD pin must be taken to ground after a Program/Verify cycle. FIGURE 6-2: VERIFY WAVEFORMS Beginning of Verify Cycle Data from Word 0 End of Programming Cycle PWM (Data) S2 (Clock) Bit190 Bit191 Bit 0 Bit 1 Bit 2 Bit 3 Bit 14 Bit 15 Bit 16 Bit 17 Bit190 Bit191 TWC TDV Note: If a Verify operation is to be done, then it must immediately follow the Program cycle. DS41097C-page 14 (c) 2001 Microchip Technology Inc. HCS320 TABLE 6-1: PROGRAMMING/VERIFY TIMING REQUIREMENTS Symbol TPS TPH1 TPH2 TPBW TPROG TWC TCLKL TCLKH TDS TDH TDV Min. 3.5 3.5 50 4.0 4.0 50 50 50 0 30 -- Max. 4.5 -- -- -- -- -- -- -- -- -- 30 Units ms ms s ms ms ms s s s(1) s(1) s(1) VDD = 5.0V 10%, 25 C 5 C Parameter Program mode setup time Hold time 1 Hold time 2 Bulk Write time Program delay time Program cycle time Clock low time Clock high time Data setup time Data hold time Data out valid time Note 1: Typical values - not tested in production. (c) 2001 Microchip Technology Inc. DS41097C-page 15 HCS320 7.0 INTEGRATING THE HCS320 INTO A SYSTEM FIGURE 7-1: TYPICAL LEARN SEQUENCE Use of the HCS320 in a system requires a compatible decoder. This decoder is typically a microcontroller with compatible firmware. Microchip will provide (via a license agreement) firmware routines that accept transmissions from the HCS320 and decrypt the hopping code portion of the data stream. These routines provide system designers the means to develop their own decoding system. Enter Learn Mode Wait for Reception of a Valid Code Generate Key from Serial Number Use Generated Key to Decrypt Compare Discrimination Value with Fixed Value 7.1 Learning a Transmitter to a Receiver A transmitter must first be 'learned' by a decoder before its use is allowed in the system. Several learning strategies are possible, Figure 7-1 details a typical learn sequence. Core to each, the decoder must minimally store each learned transmitter's serial number and current synchronization counter value in EEPROM. Additionally, the decoder typically stores each transmitter's unique crypt key. The maximum number of learned transmitters will therefore be relative to the available EEPROM. A transmitter's serial number is transmitted in the clear but the synchronization counter only exists in the code word's encrypted portion. The decoder obtains the counter value by decrypting using the same key used to encrypt the information. The KEELOQ algorithm is a symmetrical block cipher so the encryption and decryption keys are identical and referred to generally as the crypt key. The encoder receives its crypt key during manufacturing. The decoder is programmed with the ability to generate a crypt key as well as all but one required input to the key generation routine; typically the transmitter's serial number. Figure 7-1 summarizes a typical learn sequence. The decoder receives and authenticates a first transmission; first button press. Authentication involves generating the appropriate crypt key, decrypting, validating the correct key usage via the discrimination bits and buffering the counter value. A second transmission is received and authenticated. A final check verifies the counter values were sequential; consecutive button presses. If the learn sequence is successfully complete, the decoder stores the learned transmitter's serial number, current synchronization counter value and appropriate crypt key. From now on the crypt key will be retrieved from EEPROM during normal operation instead of recalculating it for each transmission received. Certain learning strategies have been patented and care must be taken not to infringe. Equal ? No Yes Wait for Reception of Second Valid Code Use Generated Key to Decrypt Compare Discrimination Value with Fixed Value Equal ? Yes Counters Sequential ? Yes No No Learn successful Store: Serial number Encryption key Synchronization counter Learn Unsuccessful Exit DS41097C-page 16 (c) 2001 Microchip Technology Inc. HCS320 7.2 Decoder Operation 7.3 Figure 7-2 summarizes normal decoder operation. The decoder waits until a transmission is received. The received serial number is compared to the EEPROM table of learned transmitters to first determine if this transmitter's use is allowed in the system. If from a learned transmitter, the transmission is decrypted using the stored crypt key and authenticated via the discrimination bits for appropriate crypt key usage. If the decryption was valid the synchronization value is evaluated. Synchronization with Decoder (Evaluating the Counter) The KEELOQ technology patent scope includes a sophisticated synchronization technique that does not require the calculation and storage of future codes. The technique securely blocks invalid transmissions while providing transparent resynchronization to transmitters inadvertently activated away from the receiver. Figure 7-3 shows a 3-partition, rotating synchronization window. The size of each window is optional but the technique is fundamental. Each time a transmission is authenticated, the intended function is executed and the transmission's synchronization counter value is stored in EEPROM. From the currently stored counter value there is an initial "Single Operation" forward window of 16 codes. If the difference between a received synchronization counter and the last stored counter is within 16, the intended function will be executed on the single button press and the new synchronization counter will be stored. Storing the new synchronization counter value effectively rotates the entire synchronization window. A "Double Operation" (resynchronization) window further exists from the Single Operation window up to 32K codes forward of the currently stored counter value. It is referred to as "Double Operation" because a transmission with synchronization counter value in this window will require an additional, sequential counter transmission prior to executing the intended function. Upon receiving the sequential transmission the decoder executes the intended function and stores the synchronization counter value. This resynchronization occurs transparently to the user as it is human nature to press the button a second time if the first was unsuccessful. FIGURE 7-2: Start TYPICAL DECODER OPERATION No Transmission Received ? Yes No Does Serial Number Match ? Yes Decrypt Transmission Is Decryption Valid ? Yes No Is Counter Within 16 ? No No Is Counter Within 32K ? Yes Save Counter in Temp Location Yes Execute Command and Update Counter No The third window is a "Blocked Window" ranging from the double operation window to the currently stored synchronization counter value. Any transmission with synchronization counter value within this window will be ignored. This window excludes previously used, perhaps code-grabbed transmissions from accessing the system. Note: The synchronization method described in this section is only a typical implementation and because it is usually implemented in firmware, it can be altered to fit the needs of a particular system. (c) 2001 Microchip Technology Inc. DS41097C-page 17 HCS320 FIGURE 7-3: SYNCHRONIZATION WINDOW Entire Window rotates to eliminate use of previously used codes Blocked Window (32K Codes) Stored Synchronization Counter Value Double Operation (resynchronization) Window (32K Codes) Single Operation Window (16 Codes) DS41097C-page 18 (c) 2001 Microchip Technology Inc. HCS320 8.0 ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Item Supply voltage Input voltage Output voltage Max output current Storage temperature Lead soldering temp ESD rating Rating -0.3 to 13.3 -0.3 to 13.3 -0.3 to VDD + 0.3 25 -55 to +125 300 4000 Units V V V mA C (Note) C (Note) V TABLE 8-1: Symbol VDD VIN VOUT IOUT TSTG TLSOL VESD Note: Stresses above those listed under "ABSOLUTE MAXIMUM RATINGS" may cause permanent damage to the device. TABLE 8-2: DC CHARACTERISTICS Commercial(C):Tamb = 0C to +70C Industrial(I):Tamb = -40C to +85C 3.5V < VDD < 13.0V Parameter Operating current (avg) Sym. ICC Min Typ* 0.6 2.0 10.0 1 Max 1.0 3.0 15.0 10 VDD+ 0.3 0.15 VDD 0.11 VDD Unit mA Conditions VDD = 3.5V VDD = 6.6V VDD = 13.0V (Figure 8-1) Standby current High level Input voltage Low level input voltage High level output voltage Low level output voltage LED sink current Pull-down Resistance; S0,S1,S2, SHIFT Pull-down Resistance; PWM Note: ICCS VIH VIL VOH VOL ILED RS0-3 RPWM 5.0 11.0 40 80 0.4 VDD -0.3 0.5 VDD A V V V V mA K K IOH = -2 mA IOL = 2 mA VDD = 6.6V VDD = 13.0V VIN = 4.0V VIN = 4.0V 6.5 14 60 120 9.0 20 80 160 Typical values are at 25C. (c) 2001 Microchip Technology Inc. DS41097C-page 19 HCS320 FIGURE 8-1: TYPICAL ICC CURVE OF HCS320 12.0 10.0 8.0 mA 6.0 4.0 2.0 0.0 2 3 4 5 6 7 8 VBAT [V] 9 10 11 12 LEGEND 13 Typical Maximum Minimum DS41097C-page 20 (c) 2001 Microchip Technology Inc. HCS320 FIGURE 8-2: POWER-UP AND TRANSMIT TIMING Multiple Code Word Transmission Button Press Detect TBP TTD TDB PWM Output Code Word 1 TTO Code Word 2 Code Word 3 Code Word 4 Code Word n Button Input Sn FIGURE 8-3: POWER-UP AND TRANSMIT TIMING REQUIREMENTS VDD = +3.5 to13.0V Commercial (C): Tamb = 0C to +70C Industrial (I): Tamb = -40C to +85C Parameter Time to second button press Transmit delay from button detect Debounce delay Auto-shutoff time-out period Symbol TBP TTD TDB TTO Min 10 + Code Word Time 10 6 22 Max 27 + Code Word Time 27 15 77 Unit ms ms ms s (Note 2) Remarks (Note 1) Note 1: TBP is the time in which a second button can be pressed without completion of the first code word and the intention was to press the combination of buttons. 2: The Auto-shutoff time-out period is not tested. FIGURE 8-4: CODE WORD FORMAT TE TE TE LOGIC `0' LOGIC `1' Bit Period TBP 50% Duty Cycle Preamble TP Encrypted Portion of Transmission THOP Fixed Portion of Transmission TFIX Guard Time TG Header TH (c) 2001 Microchip Technology Inc. DS41097C-page 21 HCS320 FIGURE 8-5: CODE WORD FORMAT: PREAMBLE/HEADER PORTION P1 23 TE 50% Duty Cycle Preamble P12 10 TE Header Bit 0 Bit 1 Data Bits FIGURE 8-6: CODE WORD FORMAT: DATA PORTION Serial Number Button Code MSB S3 S0 S1 S2 Status VLOW RPT LSB Bit 0 Bit 1 Header MSB LSB Bit 30 Bit 31 Bit 32 Bit 33 Bit 58 Bit 59 Bit 60 Bit 61 Bit 62 Bit 63 Bit 64 Bit 65 Fixed Portion Guard Time Encrypted Portion TABLE 8-3: CODE WORD TRANSMISSION TIMING REQUIREMENTS Code Words Transmitted All Typ. 400 1200 9.2 4.0 38.4 40.8 79.6 833 Max. 620 1860 14.3 6.2 59.5 63.2 123.5 266.7 538 1 out of 2 Min. 140 420 3.2 1.4 13.4 14.3 28.1 60.4 Typ. 200 600 4.6 2.0 19.2 20.4 39.8 Max. 310 930 7.1 3.1 29.8 31.6 61.7 1 out of 4 Min. 70 210 1.6 0.7 6.7 7.1 13.8 Typ. 100 300 2.3 1.0 9.6 10.2 19.9 43.0 Max. Units 155 465 3.6 1.6 14.9 15.8 30.6 66.5 s s ms ms ms ms ms ms bps VDD = +3.5 to 13.0 Commercial(C):Tamb = 0C to +70C Industrial(I):Tamb = -40C to +85C Symbol TE TBP TP TH THOP TFIX TG -- -- Note: Characteristic Basic pulse element PWM bit pulse width Preamble duration Header duration Hopping code duration Fixed code duration Guard Time Total Transmit Time PWM data rate Number Min. of TE 1 3 23 10 96 102 199 430 -- 280 840 6.4 2.8 26.9 28.6 55.6 1190 120.3 172.0 86.0 133.3 29.9 2381 1667 1075 4762 3333 2151 The timing parameters are not tested but derived from the oscillator clock. DS41097C-page 22 (c) 2001 Microchip Technology Inc. HCS320 FIGURE 8-7: HCS320 TE VS. TEMP (BY CHARACTERIZATION ONLY) 1.7 1.6 1.5 1.4 1.3 TE 1.2 1.1 1.0 0.9 0.8 0.7 TE Max. VDD = 3.5V VDD = 5.0V TE Max. VDD = 5.0V Typical VDD = 5.0V TE Min. 0.6 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 TEMPERATURE (c) 2001 Microchip Technology Inc. DS41097C-page 23 HCS320 9.0 9.1 PACKAGING INFORMATION Package Marking Information Example 8-Lead PDIP (300 mil) XXXXXXXX XXXXXNNN YYWW HCS200 XXXXXNNN 0025 8-Lead SOIC (150 mil) Example XXXXXXX XXXYYWW NNN HCS200 XXX0025 NNN Legend: XX...X Y YY WW NNN Customer specific information* Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. * Standard PICmicro device marking consists of Microchip part number, year code, week code, and traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. DS41097C-page 24 (c) 2001 Microchip Technology Inc. HCS320 9.2 Package Details 8-Lead Plastic Dual In-line (P) - 300 mil (PDIP) E1 D 2 n 1 E A A2 c L A1 eB B1 p B Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width Molded Package Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic Units Dimension Limits n p A A2 A1 E E1 D L c B1 B eB MIN INCHES* NOM 8 .100 .155 .130 .313 .250 .373 .130 .012 .058 .018 .370 10 10 MAX MIN .140 .115 .015 .300 .240 .360 .125 .008 .045 .014 .310 5 5 .170 .145 .325 .260 .385 .135 .015 .070 .022 .430 15 15 MILLIMETERS NOM 8 2.54 3.56 3.94 2.92 3.30 0.38 7.62 7.94 6.10 6.35 9.14 9.46 3.18 3.30 0.20 0.29 1.14 1.46 0.36 0.46 7.87 9.40 5 10 5 10 MAX 4.32 3.68 8.26 6.60 9.78 3.43 0.38 1.78 0.56 10.92 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 (c) 2001 Microchip Technology Inc. DS41097C-page 25 HCS320 8-Lead Plastic Small Outline (SN) - Narrow, 150 mil (SOIC) E E1 p D 2 B n 1 h 45 c A A2 L A1 Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic Units Dimension Limits n p A A2 A1 E E1 D h L c B MIN .053 .052 .004 .228 .146 .189 .010 .019 0 .008 .013 0 0 INCHES* NOM 8 .050 .061 .056 .007 .237 .154 .193 .015 .025 4 .009 .017 12 12 MAX MIN .069 .061 .010 .244 .157 .197 .020 .030 8 .010 .020 15 15 MILLIMETERS NOM 8 1.27 1.35 1.55 1.32 1.42 0.10 0.18 5.79 6.02 3.71 3.91 4.80 4.90 0.25 0.38 0.48 0.62 0 4 0.20 0.23 0.33 0.42 0 12 0 12 MAX 1.75 1.55 0.25 6.20 3.99 5.00 0.51 0.76 8 0.25 0.51 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057 DS41097C-page 26 (c) 2001 Microchip Technology Inc. HCS320 ON-LINE SUPPORT Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site. Systems Information and Upgrade Hot Line The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-792-7302 for the rest of the world. Connecting to the Microchip Internet Web Site The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: * Latest Microchip Press Releases * Technical Support Section with Frequently Asked Questions * Design Tips * Device Errata * Job Postings * Microchip Consultant Program Member Listing * Links to other useful web sites related to Microchip Products * Conferences for products, Development Systems, technical information and more * Listing of seminars and events (c) 2001 Microchip Technology Inc. DS41097C-page 27 HCS320 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: RE: Technical Publications Manager Reader Response Total Pages Sent From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Device: HCS320 Questions: 1. What are the best features of this document? Y N Literature Number: DS41097C FAX: (______) _________ - _________ 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products? DS41097C-page 28 (c) 2001 Microchip Technology Inc. HCS320 HCS320 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. HCS320 /P Package: Temperature Range: Device: P = Plastic DIP (300 mil Body), 8-lead SN = Plastic SOIC (150 mil Body), 8-lead Blank = 0C to +70C I = -40C to +85C HCS320 = Code Hopping Encoder HCS320T = Code Hopping Encoder (Tape and Reel) Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. (c) 2001 Microchip Technology Inc. DS41097C-page 29 HCS320 NOTES: DS41097C-page 30 (c) 2001 Microchip Technology Inc. Microchip's Secure Data Products are covered by some or all of the following patents: Code hopping encoder patents issued in Europe, U.S.A., and R.S.A. -- U.S.A.: 5,517,187; Europe: 0459781; R.S.A.: ZA93/4726 Secure learning patents issued in the U.S.A. and R.S.A. -- U.S.A.: 5,686,904; R.S.A.: 95/5429 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microID, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2001, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified. (c) 2001 Microchip Technology Inc. DS41097C - page 31 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com ASIA/PACIFIC Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Japan Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 China - Beijing Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Rm. 531, North Building Fujian Foreign Trade Center Hotel 73 Wusi Road Fuzhou 350001, China Tel: 86-591-7557563 Fax: 86-591-7557572 EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Dayton Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 France Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Kokomo 2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387 China - Shenzhen Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Germany Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 New York 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Hong Kong Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 10/01/01 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 DS41097C-page 32 (c) 2001 Microchip Technology Inc. |
Price & Availability of HCS320
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |